Friend John Killebrew sent me some bullets awhile back ....

and I have been playing with them from time to time. Got out to the Range today and ran some through a couple 1911's.

230 gr. cast .45 ACP Bullets
[image]

[image]

I used my old ATI 1911 and the Shootists Ruger SR1911 with 2 different powder charges ..
9.0 gr. Blue Dot and 10.6 gr. Blue Dot. The 10.6 gr. load is stout and makes the old 1911 recoil a bit. Out of my ATI they average 1034 fps.

I fired several groups with each load and each gun ... these targets are about average.

ATI

[image]

RUGER

[image]

Recoil

[image]

I am sure a lot of the heavy load downrange would beat the guns up a bit. I am not using them for practice. They are saved for use during the Zombie Apocalypse.

--
Ele era velho.
Ele era corajoso.
Ele era feio.

Post reply

766 views

quoting someone else opining on a projectile profile, "now that is a bulletty looking bullet!"..... which I took to mean it looked like it would do the job intended.

I use a very similar product from missouri bullets.....

https://www.grafs.com/retail/catalog/product/productId/22419

But use "softball" load levels in case one happens into a percussion conversion cyl.

Post reply

818 views

I use that bullet in my .45s and like it a lot. Hornady used to load a FMJ bullet with that same profile in some of their factory ammo. It was great stuff, but I have not seen any in several years. Wish they still made it.

Post reply

807 views

Jeff Cooper swore by them, they had to be great, right? Then the all lead versions. I loaded thousands more on my Dillons... still shooting them up.

--
Of the Troops & For the Troops

Post reply

712 views

Impressive in both accuracy and power. I am a fan of trunicated bullets. They generally feed as well as round noses and have a nice meplat.

--
https://facebook.com/M2bKydex/

Post reply

703 views

--
Ele era velho.
Ele era corajoso.
Ele era feio.

Post reply

739 views

I would say YES, that is truckin with a 230 gr in the 45, how did the primers look??? Good shooting with a 45 and heavy loads.

Gunner

--
https://www.instagram.com/41gunner/
41 Mags rule, Baers rock!

Post reply

710 views

Look at the primers in a cartridge that has blown a cylinder wide open and maybe the top strap off a revolver. More often than not they look normal.

I was more concerned about the case being partially unsupported at the feed ramp. I have seen cases blown down through the magazine well. Makes the magazines come out of the gun really fast! :-)

But there is no swelling of the fired cases. The heavy load is a standard load in some loading manuals I have.

Here's a normal 9mm compared to an overloaded one ... it did not blow but came close.

[image]

--
Ele era velho.
Ele era corajoso.
Ele era feio.

Post reply

732 views

The Lee 230gr TC mold was my first 45 ACP mold. I have a 6 cavity now. It is a great shooting bullet in most 45s. Blue dot is a very under appreciated powder.

Post reply

712 views

take long to empty a pot. I shoot a lot of them, with the only issue being the lube smoke at night.. reflects the light from my surefire and all I can see is a white curtain.

What lube did you use?

Post reply

735 views

RSS Feed of thread

The Frontier Sixshooter Community Message Board

To quote dean grennell.....

Friend John Killebrew sent me some bullets awhile back ....

In the 80s I loaded thousands of those Hornady FMJs Col

Looks good!

Yes. I prefer them over hollowpoints. (nt)

Stout....

Primers look normal .... But that does not always mean much.

Friend John Killebrew sent me some bullets awhile back ....

Looks good! I run two Lee six cavity moulds - doesn't ....