The Sixshooter Community Website

The Frontier Sixshooter Community Message Board

Back to the forum index

Linear

I asked about this a while back and I've forgotten much of what we discussed. It couldn't have been too negative because I haven't changed my mind about wanting a 450 Bushmaster. I'm on the ledge and just about to jump off and order an upper but before I take the plunge I'd like some feedback. I'm looking at a Bushmaster and a Windham upper and both have BCG included. I haven't looked into brass or dies but I guess I should before I buy the upper. So I'm curious if any of you have any experience with one. Can you load it with carbide dies, does it need a proprietary magazine, and are there any real negatives I need to be concerned with? Thank you in advance,

rob

1681 views

Is that a negative?

1604 views

Not for me...It can't be worse than my Guide Gun:) I did you a bit of perusing Midway's sight and didn't see any carbide dies so I'm guessing I'll have to lube cases but that's no big deal, especially on a straight wall case. Ordering the upper from Bud's gets a magazine included and it's cheaper than Midway without the mag and I'm pretty sure it's the same upper.

1649 views

Brass is expensive, but Midway has it on sale right now. I started a 458 SOCOM build just after the last brass sale ended. 450 is around $70.00/100. I have to pay about $85.00/100 because I was too slow. I went with the 458 because of all the choices in 45-70 moulds and bulk bullets.

Enjoy your cannon!

1642 views

I have shot a Bushmaster a little and it is a nice round. There are very few bullets that can handle that kind of velocity. It reminds me of the original .444 Marlin loads using a standard 240gr SP at 2400. Just way too much of a good thing. Expansion is gauranteed but penetration is limited.

The Beowulf is where it is at in the big AR cartridges. There's is a good supply of .500 S&W bullets out there that work great. Plus they are designed for the velocity. A 16" Beowulf is very similar velocity waist to a 8 5/8" .500 S&W. the 4 loads I use are a 334gr HP from rainier at 1850 FPS for a cheap plinking load, a 350 gr Speer at 1850 for a deer and hog hunting load. 375gr Barnes XPB at 1800 and for real penetration a Cast 450gr at 1550.

With bullets over 300 gr the Beowulf will outrun the other two and once you get to 450-500 it is noticeably faster.

1730 views

I was thinking exactly the same thing. You make good points on the Beowoulf, but but I just don't really want a big bore hammer. I already have a Guide Gun that more than handles the big stuff. What I really want is a 16" 44 Magnum AR and nobody has seen fit to make one. The 450 is the closest thing I've found, though it is a lot more being comparable in bullet weight and velocity to the 444. Someone needs to make a rimless 44 Mag round and carbine to go with it.

1657 views

The Automag case is made from cut down '06 or .308W class cases. The boltface for a SOCOM is .473, so all you need is a custom barrel, and to sort out the gas system. Pistol or carbine gas? Either could work, depending on the load. Same concern as if you were considering a suppressor. There are a huge number of AR wildcats out there. For that matter, there are 460 Rowland uppers available, and that could be even simpler yet.

1586 views

Would it be easier and cheaper to just buy a Ruger carbine?

1594 views

Honestly, it's just something I want in an AR and I'm not really sure why. I definitely don't need it.

1646 views

that would be relatively close to .44mag

1593 views

BTW, the 458 case is simply an overgrown 50 AE, necked down to 458.

1613 views

I killed two deer with the Rainier HP last winter; they worked quite well. Feeding is just fine out of a cheap 20 round Thermold mag, and components are plentiful. Recoil is much milder than my Guide Gun.
Quite a few guys up here are using the .450 now that the state is allowing use of “pistol-caliber carbines”, as long as it is a straight-wall case. Apparently the proprietary Bushmaster magazine is the way to go with that round, as guys were having trouble feeding it from standard 5.56 mags.

1548 views

those that shoot 44's and those that wish they did.

1610 views

...

1554 views

I've heard nothing good about Bushmaster since the Remington buyout. I'd go Windham for the upper. That being said, I have zero experience with the round. All my ARs were .223 and 6.8. Lost them all in a boating accident!

1567 views

I'll probably just pass on this 450 thing. I don't need another caliber to load for. That's too bad about that boating accident...such a shame. I was helping a friend run a bunch of branches and limbs through an industrial chipper and mine was grabbed with a pile of brush and summarily ground to bits so I do understand.

1599 views

RSS Feed of thread

powered by my little forum