Uberti Cattleman Feedback?
by Sarge 
, Central Misery, Saturday, September 03, 2016, 15:14 (2941 days ago)
My last experience with these was about 45 years ago, a 7 1/2" Iver Johnson in 357. It shot fine and was well regulated enough that I killed a bunch of squirrels with 38 wadcutters... knocked them outta the tree like they'd been hit with a pool cue.
I'm looking hard at a 4 3/4" Ranch Hand in 45 Colt and would like some feedback from any of you folks who have an Uberti in that caliber. I am particularly interested in how close your sights were regulated and if yours prefer .452 or .454 bullets.
I also see Uberti offers a Cattleman II with an elaborate linkage through the hammer that locks the firing pin in place when the trigger is pulled. Might be the greatest thing since sliced bread but I'll let somebody else be the beta tester for that.
Thanks in advance for your input.
Uberti Cattleman Feedback?
by Creeker , Hardwoods, Saturday, September 03, 2016, 21:09 (2941 days ago) @ Sarge
Looking forward to this thread.
Yes Sir and at the very least, Boge needs to...
by Sarge , Central Misery, Saturday, September 03, 2016, 22:18 (2941 days ago) @ Creeker
post a photo or two of that fine engraved one he has.
Lynn...
by Sarge , Central Misery, Tuesday, September 06, 2016, 08:54 (2939 days ago) @ Creeker
I posed this question a couple other places and got a few responses as to bore/throat dimensions, etc. They are here if you'd like to see them.
http://singleactions.proboards.com/thread/18002/uberti-cattleman-feedback
http://www.24hourcampfire.com/ubbthreads/ubbthreads.php/topics/11414781/Uberti_Cattlema...
Uberti Cattleman Feedback?
by Bob Hatfield , Monday, September 05, 2016, 06:40 (2940 days ago) @ Sarge
I have an Uberti Millenium in 45 Colt that I bought back in 2000 from Cabelas.
Here is my story. Gun shot left about 6 inches at 25 yards. So I bent the front sight back over to the left to correct. Looked like a banana. Should have rotated the barrel maybe. I should have not messed with the sight until I had several hundred rounds through it because the gun started shooting to the right so I bent it back straight and broke it off. So I soldered a new one back in the factory position and all was well except for buggering up the finish.
After a while my load of 8 grains of 231 and a 255 grain 3D RNFP (super accurate in my 45 guns) started battering the firing pin area on the breech (no bushing) to where primer material was flowing back into the firing pin hole locking the gun up. Had to help turn the cylinder sort of like a gobbed off percussion revolver LOL to shear the primer material to shoot the next shot.
So I had the firing pin hole tig welded up and tried to file it flat and couldn't. Had to grind it as the tig weld was harder than the file. Did a nice job. Had to drill a new firing pin hole in from the rear.
I reduced my standard 45 load down to 7.1 grains of 231.
Overall I am satisfied with the gun as the problems I had were ME and I only paid IIRC $219? in the year 2000 It still shoots great and timing is perfect. Looks a little worn though
Bob
Uberti Cattleman Feedback?
by Sarge , Central Misery, Monday, September 05, 2016, 09:24 (2940 days ago) @ Bob Hatfield
Thanks for the detailed info Bob. Sometimes you gotta go hammer & tongs on 'em LOL.