The Sixshooter Community Website

The Frontier Sixshooter Community Message Board

Back to the forum index

Linear

High Standard suppressed 22 auto of Bill Donavan OSS fame.

This old Ruger Standard was a complete train wreck, to include a drilled out chamber and sprung gripframe. Many gouges and abuses. It looked like a good candidate for prototyping. The barrel was replaced with a slice out of a AR barrel, 1-9" twist. Really wanted to be able to shoot the Aguila 60gr bullets and was curious how the slightly oversize dimensions and fast twist would work.

Nothing special on the inside, just K-baffles and the 4.3" barrel is ported very near the muzzle into a reflex area over the .400" diameter barrel.

Made a new taller rear sight to suit the front. Added a Volq extended mag release.

Bead blasted everything and coated in Norrel's Moly Resin Grayish-Black. Cured at a slightly higher temp to turn it greenish similar to Parkerizing that has been stored in cosmolene.

Shoots good, but the 60gr Aguila ammo is unobtainable right now.

Plan to use this as a test mule in my shop for various ideas.

712 views

.

622 views

.

593 views

Very cool!! I like the look and that rear sight is really neat! I am having paperwork drawn up for a trust hopefully to speed up the transfer go my new Sterling, but I also plan on form 1'ing an integral .300 blk can on an 8.5" barrel I have. Seems cooler than sbr'ing the lower and running it with my .30 cal can.

Is that endcap so you can disassemble it? Do you have to hook the baffle stack and pull it out or does the outer tube come off? Any issues shooting standard .22's through the slightly larger bore?

610 views

Tube is threaded both ends for easy cleaning - a must on 22 cans. So far, the bore size hasn't seemed to be an issue but I intend to bench it and compare scientifically. This from shooting 40gr standard and HV ammo of different makes.

The Form 1 integral 300 BLK sounds interesting. Do you have a design in mind? K-baffles?

578 views

I'm going cheap and simple! I don't have a lathe to work with, so I'm going to do the "freeze plug" design. I've read of several guys doing 5.56 cans with that design and holding up quite well, i figure the low pressure .300 will be just fine. Ie got the AR built up as a pistol now, sot eh barrel is already threaded. I found a slip over flash hider that I can use to line everything up, and work like a reflex style can. Make it up and weld it to my barrel, keeping it over 16" and tuck it under the YHM tube on there. Figure it's worth $200 to play with it! I've done a lot of reading on the silencer smithing forum at silencer talk.com and it looks like something I can do. I need to do a little more thinking and figure out how many baffles, spacing, etc I can have and gather materials to get a rough idea of weight.

576 views

I have studied a lot of baffle designs there. Some of the Form 1 builds are quite interesting.

Expect you are right on the freeze plug baffle working just fine; the only drawback compared to a commercial can might be weight. In a shorter integral you might not even notice the difference.

Can't make up my mind on my Noveske 300BLK upper. Probably clipped cones, eventually.

572 views

I've been reading on their silencer smithing forum for years! Lots of interesting ideas and plenty of experience.

I was trying to think of some way to lighten it all up, but like you said, I doubt it will be too bad with an integral. My SAS can is pretty heavy, so with it on the pistol, it's noticeably front heavy. It is built to withstand basically any .30 cal round, and full auto, so it's a bit on the hefty side!

Back to silencer talk, I've tried to sign up before, but they won't accept a hotmail address for registration. I've had my email for about fifteen plus years, but they still look at it Asa. Throw away email. I've tried to email somebody on the sight to see about registering, but to no luck. I rarely have anything to add, but it would be nice to post on There occasionally.

569 views

nt

584 views

Nothing in the inbo or junk mail folder.

520 views

Oops - check again. Sometimes I'm too clever for my own good... it should be there now...

533 views

Got it, thanks!

521 views

c'mon out, I have 2 bricks+ of the ammo!
bob

572 views

.

571 views

That Ruger is really great!! Love its looks..

579 views

.

559 views

.

576 views

.

554 views

I have always wanted a silencer but where I am at they are verbotten

568 views

MA - ouch. Definitely behind enemy lines.

564 views

That's a great use for a beater Standard model.

I take it you pressed the new barrel into the receiver as per original?
If so, what was the interference fit number?
Freeze/heat the parts to make installation easier?

You really do nice work.

556 views

HEAVILY torqued. Since this barrel was ruined anyway, it was easier to just turn off the torque shoulder in the lathe and unscrew it by hand afterwards.

Receiver nominal dimensions are 1" OD and .750" ID. The somewhat crude barrel threads measured around .805" x 20tpi.

561 views

I like it. Great concept and execution.

The 60 gr. Aguila is very interesting ammo. I ran through several boxes trying it in all my .22s and found that it would only stabilize in my 1956 Marlin 39Mountie. I used a Hanned tool on some rounds and felt it was pretty darn effective with that flat point AND greater weight.

--
Sincerely,

Hobie

548 views

a good idea, but it seems to be a lucky chance to find a gun that will stabilize them at 1-16". So I made one with a 1-9". :-D

Will report back as I'm able to test.

549 views

;-)

--
Of the Troops & For the Troops

535 views

waiting game. Words can't describe how nice it is to shoot without hearing protection in hot weather.

536 views

is a 1-16" twist as well.

--
Sincerely,

Hobie

531 views

I was under the impression they were pressed in originally. Threaded makes it easier to work on for certain.

537 views

and consider something different,

523 views

RSS Feed of thread

powered by my little forum